ZOMBIE FETTERMAN wins. Proves dems cheated massively again.

Nomad said:
Trumptard TDAK shits drawers. Proves she's a massive pansy ass again.

Looks to me like relatively few people in Pennsylvania wanted to vote for a phony-ass, self-serving carpetbagger from Joisey.

The more I see and listen to Fetterman the more I like him and the better I feel that we've got a tough, fair, intelligent stand up guy like him on our side in the US Senate.

Pennsylvania made the right choice.

Now go change your nasty shit-stank drawers.
Click to expand...

You like listening to broccoli, eh?

No, I take that back. Broccoli is smarter.
 
Text Drivers are Killers said:
Democracy doesn't work.
Click to expand...
There is no democracy.
Text Drivers are Killers said:
Elections don't work.
Click to expand...
Yes they do, if properly handled and monitored.
Text Drivers are Killers said:
There is just so much cheating. It's always been bad but it's gotten much worse the last few years because the swamp media is so anti-repub. I have never voted and that's why - all the cheating.
Click to expand...
If you truly believe this, there is only one solution, and it isn't a pretty one.

Think about what you are saying or what you are considering.
 
Geeko Sportivo said:
I agree with you about Oz being a bad candidate.

He seemed like he didn't do his homework to even run in this state. He was an outsider out of touch with the natives. I've seen some newsreels where he was asked by people at town halls to name just one player on the Eagles or Steelers and couldn't do it. He couldn't name the state flower or state symbol or motto. In fact, he had to turn around and look for a State Flag to even say what he thought was on it- and still didn't realize that was the Coat Of Arms on the flag.

The good people of Pennsylvania are prouder of their state than to turn it over to outsiders who don't care about the same things they care about.

And to tell the truth, Oz just never seemed sincere about anything he said. He seemed to just ramble and parrot on with rhetoric and Conspiracy theories that someone briefed him on and told him to say.

I was not a bit surprised by the outcome- only that he actually drew the race closer than I predicted.
Click to expand...

Yet the 'good people of Pennsylvania' received and counted votes from people living in New York. They voted twice, you see.
 
Into the Night said:
They cheated in the usual way, mostly in Philadelphia. Ballot harvesting and the use of 'mules', counting with no observers present, large numbers of mail-in ballots, etc. Another twist that was added this time was the thugs Biden sent to 'ensure compliance'.
Click to expand...
Thank GOODNESS for election fraud, whereby only the printing, distribution, assembling, collection, and submission of ballots matters (thus the voter himself can be safely ignored)! "Our democracy" has "been saved"!!! HIP HIP HOORAY!!!!
 
RB 60 said:
I retired from the machinist trade 4 years ago. I took the security job because I got bored.
I made parts from blueprints you couldn't read. I made cams on a lathe by drilling offset
centers. I've turned 4 ft. long shafts holding a tolerance of .0003 the whole length.
I was good at it. I was a perfectionist. That's why I became the manager.
Click to expand...


Fucking Arby was actually skilled in a worthwhile endeavor!

Machinists are important.

They alter my golf clubs with blatantly non-conforming face grooves.
I can make a ball spin backwards hitting onto Route 95 thanks to those grooves.
 
RB 60 said:
Not as much as in the past. The congested cities have lots of stupid people.
Click to expand...

Therin lies the republican's problem. Large cities filled with voters that have been conditioned to the government taking care of them, rent as opposed to becoming a homeowner, and childless thus abortion is a huge issue. I call them the lazy selfish bunch that are easy to manipulate. I doubt many of them had any real knowledge as to what is happening to their freedoms or what is going on around them. My god, in MN one transgender candidate, got 10.000 votes and he/she/alphabet has been dead for months. I believe there were two dead candidates actually voted into office. Much like the idiot we call POTUS.
It is a sad departure from what America once was. I blame the current state on sloppy immigration, the steep decline in education, and one parent families.
 
NiftyNiblick said:
Fucking Arby was actually skilled in a worthwhile endeavor!

Machinists are important.

They alter my golf clubs with blatantly non-conforming face grooves.
I can make a ball spin backwards hitting onto Route 95 thanks to those grooves.
Click to expand...

Yep. A master machinist and toolmaker.

I could crosshatch those clubs to make the ball curve 20 degrees in either direction over 100 yards.
I can drill a crosshole (and have done it 100s of times) in a hypodermic needle and resharpen the drill bit.
I made tapered internal threads by inverting the threading tool and running the lathe in reverse, and made
the threading tool offset on the required angle for clearance. I've made molds and dies. I could go on and on

So yeah, I am skilled in a worthwhile endeavor. One they don't teach in schools anymore. It's all CNCs and inserts now.
 
RB 60 said:
I retired from the machinist trade 4 years ago. I took the security job because I got bored.
I made parts from blueprints you couldn't read. I made cams on a lathe by drilling offset
centers. I've turned 4 ft. long shafts holding a tolerance of .0003 the whole length.
I was good at it. I was a perfectionist. That's why I became the manager.
Click to expand...

BFD.

Any uneducated lummox can learn how to operate a lathe if they work at it long enough.

I bet you could have NEVER learned how to create and draft those drawings you worked off of.

That is where all the knowledge and calculation occurs. You were just following someone else's instructions.

RB 60 said:
Yep. A master machinist and toolmaker.

I could crosshatch those clubs to make the ball curve 20 degrees in either direction over 100 yards.
I can drill a crosshole (and have done it 100s of times) in a hypodermic needle and resharpen the drill bit.
I made tapered internal threads by inverting the threading tool and running the lathe in reverse, and made
the threading tool offset on the required angle for clearance. I've made molds and dies. I could go on and on

So yeah, I am skilled in a worthwhile endeavor. One they don't teach in schools anymore. It's all CNCs and inserts now.
Click to expand...

Nothing wrong with taking pride in the work one has done.

Assuming you're even telling the whole truth and not exaggerating, which is open to question.

What is sad and dysfunctional, is when you typical right-wing blowhard braggarts are so insecure about yourselves, that you have to boast about how great you think you once used to be, to strangers on a message board who couldn't care less and see you as an ignorant jackass anyway, no matter what greasy, sweaty blue collar job you used to do before becoming a night watchman.

Up your game on social issues and politics and maybe you'll get the respect you crave but don't get because you make yourself out to be an ignorant jerk.
 
Nomad said:
BFD.

Any uneducated lummox can learn how to operate a lathe if they work at it long enough.
Click to expand...

Wrong. Manual lathe work beyond simple turning of parts requires considerable math skills. For example, thread cutting requires being able to grind you cutting tools precisely, setting the speed of the feed and rotation so that the threads are cut at the proper angle and distance as the tool moves down the work. Cutting radii requires special tooling and set ups. Finish on the part requires an understanding of cutting tool shapes, feed and rotation speeds, to get the proper cut for that finish.
It also requires understanding metallurgy to a degree as you have to know how the metal you are working with acts under various conditions. Turning brass is different than bronze, and steels vary widely by grade as to how they act. Aluminum is different too.

I bet you could have NEVER learned how to create and draft those drawings you worked off of.
Click to expand...

In my case, that would be a very bad bet on your part. I'd bet RB can create drawings particularly working drawings as that's usually something the machine operator does as part of their job.

That is where all the knowledge and calculation occurs. You were just following someone else's instructions.
Click to expand...

You've obviously never done machine work. NC and CNC machines require programming and math skills on the part of the operator. Manual machining with or without DRO require understanding how to set up the work. Bet you have no idea what that's for or the math needed to use it.

6-super-spacer-rotary-indexing-fixture-14.gif
 
Lionfish said:
Not cheating. Divide the Fetterman voters into three camps.
1. Republicans who strongly dislike OZ
2. Voters who understood Fedderman will be rep[laced by a Governors choosing
3. Just plain ignorant voters.

No need to cheat, Oz never had a chance.
Fetterman, as long as he remains, will become the AOC meme of the senate.
Click to expand...

Bingo.
 
Lionfish said:
Not cheating. Divide the Fetterman voters into three camps.
1. Republicans who strongly dislike OZ
2. Voters who understood Fedderman will be rep[laced by a Governors choosing
3. Just plain ignorant voters.

No need to cheat, Oz never had a chance.
Fetterman, as long as he remains, will become the AOC meme of the senate.
Click to expand...

Just plain ignorant voters are those who voted for Trump and or his lackeys.
 
You must log in or register to reply here.
Back
Top